Find an experienced handyman in Ashburton

Hi! I'm looking for someone to help with assembling and installing a garden shed in Ashburton. Here are the details: Job Requirements: 1. Ground Preparation: - Level and compact the ground surface (currently gravel base) - Ensure proper drainage - Area size: 1.5m x 3m 2. Shed Assembly and Installation: - Assemble 1.5m x 3m Skillion Roof Shed (brand new, will be provided) - Install the shed on the prepared ground - Secure the shed using ground pegs (grass pegs will be provided) - Ensure the shed is level and properly aligned Location: Ashburton, VIC 3147 Materials Provided: - New 1.5m x 3m Skillion Roof Shed kit - Ground pegs for installation - The site already has gravel base Required Skills: - Experience in shed assembly and installation - Own tools for assembly - Knowledge of ground preparation and levelling - Attention to detail - Physical capability to handle shed components Note: Must have public liability insurance and provide photos of previous work if possible.

Removal of outdoor blinds without any damage. Please refer to the pics

Replace iron burnt mark on carpet - around 13cm. You can use the carpet from within the internal wardrobe but need to be replaced with something similar.

We are pulling out a wall today and found that the roof heights in two adjacent rooms are 60mm different. Is anyone able to re player ceiling in the next week please?

For an RC plane project, need to fabricate a solar panel with high efficiency monocrystalline solar cells on top of polystyrene foam sheet to produce 500 Watts under a few kilograms. Will pay for materials

I am replacing a dry wall which was taken out many years ago, I have a builder that is doing the wall frame, connecting it and hanging the plaster sheets. I need a plasterer to blend the replacement walls into the existing walls. Need to supply materials.

Need a medium dog door installed on my double glazed window (80X70cm)

This is an old door to the sunroom which has the rolling parts not working

I need some help to tighten the fixing screws for the cat door (pic 1) and to affix the remaining part of cat run with small bendable metal wires(provided). I suspect the job shouldn’t take more than 20mins.

Need to hang 3 floating shelves in plasterboard. 10-20kg wall anchors required

Gate Door Latch needs to be repaired/ replaced.

Garage door was clunking after adjustment. Now springs and cables need setting up, maybe repair.

I need 3 flyscreens made up in white aluminium. 3 different sizes. I'm fairly confident myvmeasurements are exact but you may want to check them in person.. Fibreglass mesh is fine. I'm not 100% sure on the window recess measurement, the measurements given are internal to internal 1025w x 1145h 850w x 1390h 565w x 945h

Hang 1 artificial plant disc in outdoor area. Need 2 screws installed into timber fence and 2 hangers attached to plant (see pics).

I need a qualified electrician to replace a ceiling fan in my home. The current fan’s motor has stopped working, so I’ll supply the replacement fan; I just need help with the installation. Requirements: • Licensed electrician with experience in ceiling fan installation • Must bring necessary tools for safe and efficient installation

Need the flywire of a external sliding door replaced. (see pics) You may need to visit first to measure and see what else may be needed but overall a relatively simple job.

We have 1 poster we would like to hang on our office wall. If you know how to accurately hang a picture frame on a wall then this task is for you. need to bring your own equipment.

We have an area where the paint has peeled and there is some rot underneath. Need quote and possible solutions Ground floor. Window is approx 2.3 off the garden bed outside

Measure and Quote for a unit that is about to be sold - Need some carpet samples and somone with a good eye for what colour suits best.

Our bottom gate latch has come loose and the swing gate has dropped a little (so it does not close properly). We need someone to re-attach the metal latch to the metal post. You will need to drill a new hole on the other side of the post and then thread a long screw throgh. I thnk I have some spare screws. We have done this for the top latch but not the bottom. See photos which shoulkd explain what I mean.