Find an experienced handyman in Oaklands Park

I am upgrading my wardrobe sliding doors and I need to prepare the area by removing the current doors + track. Photos can be sent on Monday - they are standard white melamine & mirror doors. Needs to be done by Wednesday.

I need to install a railing in my wadrobe to hang clothes. Materials are needed

Need a single leaf internal masonry wall professionally removed (3.5m long x 2.4m high). I will supply and install the propping however I need someone to supply & install temporary wall & floor protection to control all dust & debris and dust extraction system to be provided as house is being occupied. All rubbish to be cleared/ removed post wall removal.

Need to build a glass door on three side of wall 3x3 on three side

Glass door 3 side of the wall

Our bathroom door is broken, so I need a new door and have it installed.

Hanging stuff on a brick wall

Hard to move, open and close

I just need to have a curtain rod installed in our bedroom but I don’t have tools to do it. It’s dry wall so you’ll need to come prepared with the correct tools for that. There is a Bunnings nearby if you’d like to come and assess what you’ll need first.

Need to install an EasyShed (narrow slider garden shed)

We have double view blinds on 2 windows. They both have been woven all the way down and wont go up. One of the brackets has come away from the window frame.

Hi, I need handyman service to drill a whole in the laundry area. Location- Sturt Need to be done today

This job is to install the hooks that will hold 2 x acoustic panels on the ceiling. Panels measure 1220x590. By the looks you'll need a large square as I don't have one to ensure they are straight. I have a laser that might work though haha. I have a tall ladder and a drill. The ceiling is about 2.6m. I can hang the panels easily enough as they are only 9kg. Instructions from the website are below. Just need someone with experience to help me mark out and install 8 hooks. 1. Measure and mark out along the ceiling from the wall where you would like a corner of your panel to be. 
Note: the panel will hang from chain at each corner of the product at the rear, see example image. 2. Measure and mark out again from the wall, 1210mm (long end) down from the first mark. Measure the distance between the two markings to confirm. This will be your second corner.
  3. If you have a laser line, point the line at the ceiling between the two markings, with the cross section at one of the marks (assuming it has a cross section). The lasers should be parallel with the walls.

If you don’t have a laser line, use a large square (with measurements on it) instead by holding the square in the same location.

  4. Measure out from the cross section your third corner at 578mm. 5. Move the laser or square to the third corner and repeat for the forth corner. Recheck the distance between all markings. You should have four marks in a rectangular shape a fraction smaller the size of the product.

  6. Drill a 5mm pilot hole for the four marked out holes into the plaster. If you hit a stud, you can screw the hook directly into it.

  7. Place the tip of the screw into the hole and screw in slowly until flush with the ceiling. 
If there is too much resistance, drill a larger pilot hole to avoid breakage.

 

Hang dryer on wall. Instal new cupboard on wall laundry

My Aluminium gate gets stuck when open and closes , likely to do with the hinges which are worn and need replacing. Tried to unscrew the hinges but no luck (see pics) Might need an angle grinder to get the hinge screws out and replace the hinges. Fence is all metal including the post with the hinges attached. The metal post is butted up and bolted into the masonry wall. Thanks! - Due date: Flexible

U have got a huge poster picture that I would like to be framed up and hung on the wall. Probably need a custom frame maker for this. Wooden frame/ aluminium metal frame is ok whatever that is most cost efficient. - Due date: Before Friday, February 23, 2024

Installation of 1 Venetian blind in the kitchen. The blind needs to be cut to fit the window and screwed into wall. Approximately less than 1x1m (window size) - Due date: Flexible

Fridge seals need to be replaced on 6 commercial fridge doors and railing. - Due date: Flexible

replace old shower screen with the new semi frameless shower screen for my bathroom - Price is negotiable. Due date: Flexible

Assemble & weld wall frames from pre cut 75x50x1.6 Dura Galv detailed drawings all gear provided. Just looking for someone who can read drawings, fabricate and weld - Due date: Needs to be done