Find an experienced handyman in Templestowe Lower

See attached document which explains what I'm after.

I have folding cabinet door i need reattached to its hinges today. Due to injury im unable to do this. I havr attached pics of identical door and how it folds out as well as of door that needs reattaching. Problem is one of the screws, in the door that has come apart, was partially broken and lodged in one of the anchors into which the screw goes in. Therefore need u to remove any loose broken bits and then reattach door. Please provide other screw of similar size to fit the door. See pics Templestowe Lower

Need to install two bidet attachments. One is a seat and the other a hand held attachment.

Need to do rendering to my existing plaster

I'm looking for someone to assist with installing a stainless steel board in a room. The board needs to be 180cm high, and I also require a few holes to be made for the electrical plugs. The picture is the size required, please provide the offer with materials included Requirements: - Installation of a stainless steel board (180cm high) - Drilling of holes for electrical plugs - Please include materials in your offer Budget: $500 Deadline: 31th Oct - 6 Nov If you have experience with this type of installation, please send us a offer including materials.

Need a quote to repair a spa area with concrete and bricks in Templestowe lower, flexible with day and time , photos attached

122cm long by 198cm high and attached glass side is roughly 110cm not including the 13cm wooden mid section by 198cm. This is a sliding door from the kitchen area into the patio. I also need the flyscreen changed.

Fixing the cabinet door 2 of them This one and another cabinet similar in another bathroom.

Looking for someone to replace the dog door flap. The current flap is a thick piece of hard acrylic that we would like to replace with a softer plastic material. The flap is attached to the door with pop rivets. Job will include: - remove the flap from the attachment - ⁠source and provide a softer plastic material as new door flap (Bunnings is fine) - ⁠install new door flap to existing door frame

Concrete slab 266 x 160 cm is ready. I need some one or two to assemble this shed and bolt it on the slab. https://www.bunnings.com.au/absco-sheds-2-26-x-1-52-x-2-08m-space-saver-single-door-garden-shed-woodland-grey_p3316436 Please send me quote including labour, necessary bolts, screws etc.

One side of the front gates could not open fully. Need re-adjustment or repair

Assemble small garden shed - approx 2m x 1m (brand new)

Front door is sticking on the floor. Needs removing, shaved, repaint the bottom of the door (we have the paint), and then rehung.

Two holes made by tv mounting need to be covered. TV already uninstalled.

Wanting this fold down clothesline installed onto a brick wall and thread line so fully set up and usable. Please provide fee for full task including threading the lines, bolts, etc. I have the clothesline already, task is installation only. https://www.bunnings.com.au/austral-35-6m-woodland-grey-addaline-double-fold-down-clothesline_p4510522

I have a shower screen glass 2100 x 1190 to be installed in bathroom I have the glass already, but no hardware currently Would require drilling through tiles and plaster on the wall and through tiles and concrete on the floor for installation of brackets Thanks

Licenced plasterer for removal of 90's installed cornice and (best endeavours) square-set finish. 2-bedroom house, approx 90 lineal metres (excl. bathroom/laundry) Non-consecutive work days (1 day per week). Please provide day rate and estimated days required Some materials provided; additional by cost reimbursement.

Motor is working but not rolling blinds up.

I have 3 three windows made shorter,need to fix the brick the time is flexible and live in templestowe lower and the brick probably bigger than normal brick I think if you need I can send the brick size and I don’t mind the brick color because I need print after this just take same same size brick would be fine.

I have applied silicon oil on the belt and played around with the bolts on the back of the machine. Also cleaned the motor area and applied soap (bar) on the belt. The squeaking sound seem to be coming from the deck, not the motor.