Find professional window and door services in Miranda NSW

Require a cabinet maker / carpenter to ensure that a stairway to be enclosed and a door hung in a garage so fumes from cars are stopped and privacy can be achieved. Stairway to be enclosed is approximately 2600x1000 Door to be hung 900x 2000 door and jam must be manufactured

Car bumped the garage door and damaged the internal steel frame fixation. Needs to be fixed to the wall again so the garage door mechanism can be used again.

Handyman license & insured to hang picture, door stop, clothes dryer bracket, screw table leg

I need someone to supply and install a fly screen sliding door in my apartment. Rough measurements 130cm in width and 265cm height. No existing track for fly screen door.

I’ve got a roller door, 2.5x2.4 with all brackets & tracks.Want it installed in my garage. There’s currently no door on it, just a hole cut to the right size. (Not cut yet, waiting to lock someone in to do the job)

I've bought an electric garage door roller from Bunnings and need it fitted. Clearance on the side where it needs to be fitted is pretty tight making this a bit awkward so I believe it needs two people.

As mentioned, licensed and insured handyman to hang 3 pictures, install 2 door stops, and fit Hisense dryer bracket and finish installing fold down wall clothes line.

install the garage door motor

Need to set the corner after window installation

Sliding door hard to open and close

Our garage door (roller door, with panels) and the LOWEST panel has been bent about 2-3 degrees. We don’t know whether it needs to be replaced or just bent back into shape. A person with experience with roller garage doors and cars backing up into them, fixing or replacing them, would be appreciated. See attached photo, it is only the lowest panel of the roller door, and the curve produced by the accident is only about 2-3 degrees off straight. It just doesn’t look flush. The roller door opens and closes, but does get stuck at the full open position. The roller door is automatic.

Need to remove old bathroom door frame and install a new one No need to paint

Hello, We are a reputable eyewear and healthcare company currently experiencing an issue with a sliding door at our NSW - Miranda store. The store team reported: "The issue with the backroom sliding door is that it cannot be closed at all. It jams in the middle of the door frame. We need this issue resolved as soon as possible. Yesterday, the door was functioning perfectly, but this afternoon, I noticed it won't slide at all, which is quite concerning." We need this issue rectified urgently. Store Address: 600 KINGSWAY, Miranda, 2228 (Exact location will be provided upon acceptance of the offer). We are looking for an experienced handyman/door installer who: - Has good reviews and a high resolution rate. - Has their own ladder and tools. If you are interested, please provide the following: 1. Availability (Date and time): 2. Work Scope: 3. Offer (Including all labor and material fees): Thank you very much for your attention to this job post.

We have an Aqara smart door lock D100. It has already been installed. We just need help setting it up. My husband tried to set it up and the alarm constantly goes off when the battery is in.

Need to fix the wardrobe door tracks

Bathroom door has come off too hinge. Despite attempts to drill back in, it seems the screws are not gripping to the existing holes. May need some building experience.

Install door handle to Renault master van sliding door I have a new handle ready to go

I have a 65inch tv that needs to be moved from one wall to another wall. Then I have a large mirror 50inch by 75inch to go on the wall where the tv was (this setup was used previously so is definitely possible). You will need tools to allow you to find and drill into the home’s steel frame. I will be available to help you with lifting and to do this safely between the 2 of us. Then, finally the installation of a Bunnings Door Closer to stop a door slamming in the wind. You will need to be able to provide a tax invoice. Finally I just need a line of silicon down the side of a door to stop water getting behind the wood.

Need to assemble back the Garage door as I unhooked it and don't know how to put it back together. ALSO, need to calibrate it as the remote is linked to the control unit (as I can hear it click) but the roller door doesn't move.

Fisher & paykel oven, took the door off to clean it and now the hinge won’t flick back up for me to attach the door again