Find an experienced handyman in Sydney City CBD

Air conditioner maintenance

We got a couple of tables to be fixed because are unstable

Office chair wheel broken. Need to fix the broken wheel and tighten the other wheels. Location is in Sydney CBD. Car park provided is needed.

Part of my treatment table came off, seems like the wood has a bigger hole for the screw. I would need someone to be able to put a new piece of wood and screws

Need Carpenter who can remove old door & install see through glass wall.. Door measurement: H×264cm Wx85cm I am flexible with half timber & half glass wall. Most welcome to inspection at 45 Shelley st Sydney NSW 2000 CBD Lift & parking available.

Fix the hole from the bathroom door

The previous spout was too old and has broken off from the wall. Just intending to fix the broken part. I had purchased a new spout from Bunnings. Please see pictures for more details.

Have purchased shelve brackets from Bunnings and need the holes drilled through tiles and concrete and screws installed. Total about 20 holes and screws. Should take an hour or so.

Need carpenter to put 75 inch TV on GYPROCK wall. Please give quotation with materials with finishing all necessary tast involved in it. As wall is not concrete. Location: 45 Shelley st, Sydney NSW 2000 CBD (Lift & Parking available)

Need someone with experience to remove and replace the window regulator in the left front door of my kia rio 2013. I already have the part. You just need to bring the basic tools like a screw driver and a clips remover. Job would take less than 30 min. Your job is to: 1) Remove the internal door panel cover (3 screws and few clips); 2) Remove the moisture protective plastic; 3) Remove the old window regulator; 4) Install the new window regulator; 5) Put back the moisture protective plastic; 6) Reinstall the internal door panel cover; 7) Test all functional ensuring that the electric window is going up and down normally.

Open timber Panel to access roller door We have broken Roller Door in Small Café near Town Hall Station. Timber panelling is covering roller door top mechanical parts. Need to cut timber/Gyros panel to access roller door From my experience with right tools it shouldn't take more than 15-30 min .

Different handy man jobs. Holes to close and few repairs

We have put in new sink and need carpet tiles fixed as there is a gap, wall tiles need fixing and some paint touch ups.

Tripod legged lamp, 1 leg is cross threaded (?) and therefore lamp is unstable. Don't care how it's fixed (glue, weld etc)

Labourer from 11:30 min 4h - View all the details of this offer: https://www.airtasker.com/offers/01JED4PSAFM308RH767K24SKPP

I need a the supply and installation of four angles for columns, each 2700mm in height. Only four angles are required. We will handle the sanding after you set, so your quote should cover supply and installation only and setting. It’s a job that should only take a few hours.

Labourers from 7:30. Min 6h - View all the details of this offer: https://www.airtasker.com/offers/01JCJ4YER23SJJPN3JSFWA4VH3

Greater Sydney area work installing solar. Looking for roofers and electricians. Serious pay for serious workers. Training obviously provided for the roof work but must have a can do attitude. Experienced workers preferred. Pay negotiable on experience. $2000 and up per week is achievable

16 holes and 8mm dyna-bolts installed into Darling Harbour restaurant for lighting clamps. Must be available 9am till 11am Thursday as that’s the only available work window. Must have own professional drill and masonry bits 8mm and 10mm. It’s industrial concrete so has to be a good drill. Ladder and bolts are onsite already.

We need 4 whiteboards screwed into the wall and 4 post it whiteboard stickers installed. Located on Pitt St with loading dock parking on street Screw in whiteboards 900x1500 Post it whiteboard stickers are 900x1200