Find professional window and door services in East Sydney

I am looking to close off my car port with a sliding door in front.

Install door handles to two doors (2 sets of handles). The mullion is Aluminium 50mm wide x 50mm deep. You can see in the photos the cylinder is install and hole cut already. Just need someone to position and screw into place

Need someone with experience to remove and replace the window regulator in the left front door of my kia rio 2013. I already have the part. You just need to bring the basic tools like a screw driver and a clips remover. Job would take less than 30 min. Your job is to: 1) Remove the internal door panel cover (3 screws and few clips); 2) Remove the moisture protective plastic; 3) Remove the old window regulator; 4) Install the new window regulator; 5) Put back the moisture protective plastic; 6) Reinstall the internal door panel cover; 7) Test all functional ensuring that the electric window is going up and down normally.

Installation Only. Sticker for Inside of Window H 1946mm W 2722mm Sticker for inside of Door H 2458 W 1967

We are located at Sydney, Pitt St. The door is very hard to open and close fully. It needs to be pushed extremely hard for it to close. It seems to be stuck somewhere. WD-40 has been tried. First two photos attached. The second issue is that the other half of the door is fully stuck. The bottom locking mechanism doesn't work. Latter two photos attached.

Fix door that doesn't shut properly. Need a good carpenter. Also have tile outside that needs to be put back on. Last photo is a baby gate hook that keeps coming off the wall

Replace current (damaged) door. Standard internal door will be supplied which needs to be hung reusing current hinges. Open to pre painting or painted once hung. The current door needs to be replaced and taken away.

Panels have fallen off a restaurant door and need sticking back on, some a very heavy and require securing clamping

I’ve recently had new carpets installed and they’re too thick for my bedroom door. The door needs trimming by a couple of CM and rehanging.

The rail of shop's sliding door broken and fell off, need a repair job.

The rail of shop's sliding door broken and fell off, need a repair job. Aiming to be done before 7pm.

Need a skilled carpenter to install three internal doors. They are Polyurephane painted so you will need accurate tools to not damage the door. Door jambs are existing steel jambs, hinges and handles need to be removed off the old doors and reused, Euro fittings, no locks on these three.

The door frame was bitten by a dog and needs mending

Need a trade to work with us on a bulk order. Supply install and paint door. Standard hollow door. Some hardware reused and other will require new hardware. We can provide as many jobs as required. I’ve got one ready to go as a trial basis. Need absolute best price. All over Sydney.

Fridge is on site. 8am start time would be ideal. Or after 4.30pm No parking available on site. https://www.bosch-home.com.au/productlist/fridges-freezers/fridges/freestanding-fridges-without-freezer-section/KSV33VI3A#/Tabs=section-highlights/Togglebox=accessories/Togglebox=accessoriesOthers/Togglebox=manuals/

Hi, We are from Oscar Wylee. We require to repair the door hinge of our Dispense desk door.

Broken hinges on cupboard door (2 hinges in total, one side of the door) - Need help asap as it's inside a business and creating a risk. No new hinges are required I think, just needs to be reattached. Business is inside busy shopping centre

Need carpenter for Repair bed slats center. Bring 75"TV Mountain and fix on the wall. Require lock to bedroom door and wardrobe doors. Please send most reasonable honest budget. On 10th September at 35 Shelley st Sydney CBD

I have a project at Charlestown Square needing a quote. Basically, it’s a window decal applied from the inside 12 metre wide ( only 10 drops 1200 mm wide each) x 3000 mm high. See screen shot.

Need a handyman to fix a loose Hobart dishwasher door. When the machine is running, the door doesn’t close properly. Assuming the spring needs a fix.