Find an experienced handyman in West Melbourne

My Hisense 50k3110pw just randomly started showing a horizontal line. I unplugged the hdmi cable and it is still showing. I want to check if it can be repaired under $100 or if I should replace it.

The existing blinds are in bad shape. Discussion, travel and visiting on site.

Here are the details of the work: 1. Mount two Audmore stainless steel kitchen utensil racks (length of each rack: 39.5 cm; I’ll supply you with the two racks and their instructions) on the southside plasterboard wall of my open plan kitchen/living room. In the photo of that wall provided below, I have labelled the area where it might have timber studs. That’s the area where the kitchen utensil racks need to be mounted. 2. Mount two Everhang Broom Holder Racks (width of each rack: 36 cm; I’ll supply you with the two racks) on the northside plasterboard wall of my open plan kitchen/living room. I am uncertain whether that wall has timber studs. It might have timber studs. 3. Mount one Dyson rack (I’ll supply you with the Dyson rack and its instructions) for my Dyson cordless vacuum on the plasterboard wall adjoining my living room balcony. That wall has timber studs. 4. Mount one Everhang Broom Holder Rack (width: 36 cm; I’ll supply you with the rack) on the plasterboard wall just outside my bedroom. That wall has timber studs. 5. Mount two MODE 6 Brushed Nickel Hooks On White Board Hat And Coat Racks (width of each rack: 60.3 cm; I’ll supply you with the two racks) on the plasterboard wall next to my bed. That wall has timber studs. 6. Mount one Everhang Broom Holder Rack (width: 36 cm; I’ll supply you with the rack) on the plasterboard wall just outside the spare bedroom. That wall has timber studs.

Replace cover kit for water meter. Dig out existing and install new kit. Kit supplied, byo tools and cement backfill

I have a pcb from a cooktop that needs 2 of the capacitors replaced. It’s basically remove the old and solder in the new. I will provide the replacement capacitors ( they are 470uF/25v, 10mm diameter, 16mm eight ) I can drop of the board and pick up when finished

I need pieces of plywood drilled and screwed together. I do not have a drill or the screws so you will need to provide these. The wood is part of a bed frame that was been broken during transport. The side dimensions of the wood are in the photos. The pieces of wood are 190 cm long, so they will need about 6 screws across the length of the wood to put it back together. There are 2 sides to the bed frame, each side has 2 pieces of wood each to screw together, so in total there are 4 pieces of wood to drill and screw together.

I have a wall mounted dryer that needs to be removed and disposed of. I also have an old fridge that needs to be disposed of

Hang whiteboard, pin board and acrylic sign. Need to bring necessary tools. I can help lift and hold into place so just a one man job.

I need someone to fix hooks for heavy frames in plaster walls.

Cut 4-5 PVC Panels and Wall mount drying racks

The chain as part of the blinds for my windows in my room has come off so I can’t open or close my blinds which is a hassle especially when I try to sleep during the day or need privacy. It’s been stuck like this for over a month.

Replace the plaster on each spot

Our venue has a medium- Large sized deck that needs sanding only. The deck measures roughly 9m x 7m. Would like this done in the next 2 - 3 weeks. This would need to include hammering down nails that stick out (if any). The deck is roughly 2 years old so hoping minimal screws.

I need the kitchen sink pipes to be replaced, there’s a leak at the bottom and it’s also slow draining

Replace mouldy silicon around bathtub and small shower

Looking to get my shower base re-surfaced, also clean up the caulking/grout around shower base.

Install 2 shelves in kitchen area.

Hang Mirror on wall it is approx 150cm high and 40 cm wide

I tried to fix a lock strike plate back onto a door frame where the underlying wood had been damaged & had fallen apart... well I didn't realise so much wood had fallen out even though it looked great & for well, I did it 3mm too deep with liquid nails and screws. It's really well attached now!... but the latch bolt won't go into the strike. Doh. I think it needs some new wood or something from scratch, I'm at a loss and give up. I have failed. Help?

I have two ikea shelves and a wall lamp that i need screwed up onto my wall. The apartment building i live in has metal studs in the walls so i am unable to drill a hole with my normal drill.